Jump to content
  • What's Next?

     

     

PCB Files

  1. All
  2. A
  3. B
  4. C
  5. D
  6. E
  7. F
  8. G
  9. H
  10. I
  11. J
  12. K
  13. L
  14. M
  15. N
  16. O
  17. P
  18. Q
  19. R
  20. S
  21. T
  22. U
  23. V
  24. W
  25. X
  26. Y
  27. Z
  28. #

4 files

  1. PIN2DMD EVO XL 192x64 UPDATED

    These are the files for the PIN2DMD EVO XL board I updated.
    In the file you can find the gerber, .sch, .brd, PCBWAY BOM and PDF's of the schematic and board.
    This is an updated design of version 1.1 of the PIN2DMD EVO XL 192x64 board.
    The Sega XL displays have different brands of display with their own length of ribbon cable.
    If you're lucky V1.1 will fit. If you're not lucky V1.1 needs a new ribbon cable, which is quite annoying.
    With this version you don't need a new cable because the ribbon cable connector is physicality moved to a closer location for the original ribbon cable to reach. 
     
    For more information see: https://vpuniverse.com/forums/topic/4122-pin2dmd-evo-dmd-multicolor-now-also-for-de-128x16-and-sega-192x64/page/7/#comment-60634
     
     
    !!! NOTE: The design is not tested yet, so please go over them or wait until someone else has completed an order and confirmed.
    If the design is tested I will update this download. You can also check the linked thread. !!!

    7 downloads

       (0 reviews)

    0 comments

    Submitted

  2. PIN2DMD HD SHIELD

    These are the files for the PIN2DMD HD shield I designed.
    In the file you can find the gerber, .sch, .brd, partlist, photos of the different Micro SD readers, .dxf for laser cut panel and a photo how to orientate the shield to the panel.
    This shield is designed to build a PIN2DMD HD 256x64 display.
    You can source the parts yourself. This could be cheaper than its big through hole brother. 
    For the processor it uses a 144 pin H743 NUCLEO board. 
     
    For more information see: https://vpuniverse.com/forums/topic/5348-pin2dmd-evo-hd-upgrade-to-256x64-resolution/
     
    !!! NOTE: The chinese LED panels can have the magnets/screw holes in another position than desired.
    This is the annoying thing with these chinese LED panels. !!!

    19 downloads

       (0 reviews)

    0 comments

    Submitted

  3. PIN2DMD NUCLEO HD BOARD

    These are the files for the PIN2DMD Nucleo HD board I designed.
    In the file you can find the gerber, .sch, .brd, partlist and photos of the different Micro SD readers.
    This is a newly designed version of the SMT version of the PIN2DMD EVO HD 256x64 board, with the parts in the same spot as the SMT version when this was possible.
    This version is fully through hole, so you can solder it yourself and also source parts yourself. 
    For the processor it uses a 144 pin H743 NUCLEO board. 
     
    For more information see: https://vpuniverse.com/forums/topic/5348-pin2dmd-evo-hd-upgrade-to-256x64-resolution/
     
    The picture of the black PCB is the prototype V1.0.
     
     
     
    !!! NOTE: The chinese LED panels can have the magnets/screw holes in another position than desired.
    Becasue of this, the position of the magnets/screw holes should always be checked if they will not touch any electical components on the PCB.
    If this is the case, you can simply put a piece of tape over this area. !!!

    23 downloads

       (0 reviews)

    0 comments

    Submitted

  4. DE-Sega-Stern power adapter

    This is the power adapter I designed for Data East/Sega/Stern machines.
    It plugs directly in the 15 pins connector on the different power boards and you can plug the wire connector directly into the adapter: 
    VERSION 3: CN6
    WHITESTAR: J16
    SAM: J16
     
    The 12V, GND and 5V are being tapped from the lines on the power board. They are fed to a 4 pin molex connector.
    You can use the Colordmd WPC wire harness or make your own wire harness.
     
    Note: the 5V should only be used for simple  MOD's, not to power the PIN2DMD displays. The connector labeled WPC on the PIN2DMD PCB's will not accept 5V (not connected).
    Only the 12V should be used for PIN2DMD shields or displays when using the WPC connector.
     
    Compatible with:
    Data East: Version 3
    Sega: Version 3 & Whitestar
    Stern: Whitestar & SAM

    6 downloads

       (0 reviews)

    0 comments

    Submitted


×
  • Create New...