Chesco Posted January 22, 2022 Posted January 22, 2022 Hello. I have received 10 EVO Boards from Pcbway (V1.4). I have tried to connect each of them with the computer but it is impossible: Windows detects absolutely nothing!!! I have tried on 3 computers and with several Mini USB cables and there is no way. USB 3.0 Hub between my PC and the pin2dmd... and nothing... However, another old V1.4 board is detected by the computer at first. I've read all the posts with this problem but I can't find the solution. I need help please...🤥
Content Provider lucky1 Posted January 22, 2022 Content Provider Posted January 22, 2022 Did you try with ST-Link ?
Chesco Posted January 22, 2022 Author Posted January 22, 2022 Thank you very much for your reply Lucky. I understand that I have to program the Boards in ST-Link mode. Do I need an ST-Link interface, right?
Chesco Posted January 22, 2022 Author Posted January 22, 2022 When I connect Pin2dmd to PC (Mini-USB), PC detects absolutely nothing....
Content Provider lucky1 Posted January 23, 2022 Content Provider Posted January 23, 2022 11 hours ago, Chesco said: Thank you very much for your reply Lucky. I understand that I have to program the Boards in ST-Link mode. Do I need an ST-Link interface, right? Yes ! Either that shown on your picture or if you have a Nucleo or Discovery board at hand you can use the onboard ST-Link as well. The EVO does NOT have a onboard ST-Link interface.
Chesco Posted January 23, 2022 Author Posted January 23, 2022 8 hours ago, lucky1 said: Yes ! Either that shown on your picture or if you have a Nucleo or Discovery board at hand you can use the onboard ST-Link as well. The EVO does NOT have a onboard ST-Link interface. Thanks you very much again...
Chesco Posted January 23, 2022 Author Posted January 23, 2022 Hello again. I has connected The St-Link Programer to Board and PC. I has downloaded Pin2dmd.bin file from Pin2dmd site: https://github.com/lucky01/PIN2DMD/tree/master/firmware/latest/EVO128x32_EVO128x16 Programed sucesfull whit program, but Pin2dmd don´t work after program 😟
Content Provider lucky1 Posted January 23, 2022 Content Provider Posted January 23, 2022 Try with all boards you have just in case you have another hardware problem with the board you are testing with, but I think you received fake chips.
Chesco Posted January 23, 2022 Author Posted January 23, 2022 Thanks you very much for your help and your time Lucky 😉. 5 panels programmed with ST-Link and none of them work... I will open a DISPUTE to Pcbway😡😡😡
Chesco Posted January 23, 2022 Author Posted January 23, 2022 1000€ more 300€ in TAX and they install a fake/clone STM32 Chip without quality.... 😕😕😕
Content Provider lucky1 Posted January 23, 2022 Content Provider Posted January 23, 2022 Just to be sure, check the voltages at the CPU
Chesco Posted January 23, 2022 Author Posted January 23, 2022 1 hour ago, lucky1 said: Just to be sure, check the voltages at the CPU How can I do it? Some pictures with pins and voltage? Another thing... USB Driver select and file for program is the correct? I has program with 12V input and whithout 12V input and... NO WORKS... Greetings.
Content Provider lucky1 Posted January 23, 2022 Content Provider Posted January 23, 2022 I would send those pictures to pcbway as a proof that the chips are fake !
Chesco Posted January 23, 2022 Author Posted January 23, 2022 22 minutes ago, lucky1 said: I would send those pictures to pcbway as a proof that the chips are fake ! However, using the STM32CubeProgrammer Software...
Chesco Posted January 23, 2022 Author Posted January 23, 2022 And with the same program, and a good Pin2DMD working...
Chesco Posted January 25, 2022 Author Posted January 25, 2022 Good morning. I have opened a dispute to Pcbway and, after sending the evidences (images and video) they have assumed that the installed STM32 Chips are Fake. (@lucky1 was right...) They have offered me 2 solutions: 1.- Recover my money (with this option I would lose the 250€ that I have paid in taxes in my country). 2.- Go back the Boards to China so that they can put valid STM32 Chips. My question is: can it be problematic or give future errors to remove a Chip from a Board and solder another again? I mean problems due to solder residue, bad connections... Thanks you.
Content Provider lucky1 Posted January 25, 2022 Content Provider Posted January 25, 2022 5 hours ago, Chesco said: My question is: can it be problematic or give future errors to remove a Chip from a Board and solder another again? I mean problems due to solder residue, bad connections... If you have the right equipment and skills that is no problem. I would take option one and find someone who can change the CPUs. The hard job currently is to find good ones. Maybe @Tinkertilter can help
Chesco Posted January 25, 2022 Author Posted January 25, 2022 Thanks @lucky1 The problem is to find a Valid STM32 chips at this moment... https://a.aliexpress.com/_uHnfJk
Content Provider lucky1 Posted January 25, 2022 Content Provider Posted January 25, 2022 21 minutes ago, Chesco said: The problem is to find a Valid STM32 chips at this moment... 1 hour ago, lucky1 said: Maybe @Tinkertilter can help
Chesco Posted March 3, 2022 Author Posted March 3, 2022 Hello Again. I have bought 10 Chips from this seller. It is the one that had the best ratings, but unfortunately, the Chips do not work either ... Windows USB does not recognize the Board. https://es.aliexpress.com/item/1005003247472878.html?gatewayAdapt=glo2esp&spm=a2g0o.order_list.0.0.21ef194d6zO8eV
Chesco Posted March 6, 2022 Author Posted March 6, 2022 Has anyone had the same problem recently? The latest Chips are programmed in a specific way?
Content Provider lucky1 Posted March 6, 2022 Content Provider Posted March 6, 2022 4 hours ago, Chesco said: The latest Chips are programmed in a specific way? No ! If you can´t program them in DFU they are most likely fake .
Recommended Posts
Archived
This topic is now archived and is closed to further replies.