needavirus Posted May 23, 2020 Share Posted May 23, 2020 Hi everybody ! I've just installed my new pin2dmd on my freshly restored Wipe Out, But i've a little problem. The display stay on the Splash screen, When I turn power on, I see ColorPrism 3.12, and then Gottlieb V1, or V2, V3 and it stay on this forever... The key on the SD card seems to be recognized. Of course this pinball has no colorisation so I put palette in blue. (There's only key file on SD card) I've tried Gottlieb V1, V2 and V3 and waiting for 15' each. It wont start. Have you any idea about this issue ? Thanks a lot ? Link to comment Share on other sites More sharing options...
Content Provider lucky1 Posted May 23, 2020 Content Provider Share Posted May 23, 2020 Are you sure the hardware pinball and pin2dmd is working properly ? Link to comment Share on other sites More sharing options...
needavirus Posted May 23, 2020 Author Share Posted May 23, 2020 How can I test it ? It's my only pin left with Pin2DMD on it. For the pinball itself, yes. Link to comment Share on other sites More sharing options...
Content Provider lucky1 Posted May 23, 2020 Content Provider Share Posted May 23, 2020 Did you run the input test as described on https://pin2dmd.com/ point 3 Did you test the pinball output with a plasma dmd ? Link to comment Share on other sites More sharing options...
needavirus Posted May 24, 2020 Author Share Posted May 24, 2020 RE, So, I've tested the input like in video : Without any cable it's OK (All pins OPEN) But if I put a jumper, I cannot get all pins closed, only 5 & 11... I don't know why. (Is there a problem on this point ?) And if I put another DMD plasma on it, yes it works correctly ? Thanks Link to comment Share on other sites More sharing options...
Content Provider lucky1 Posted May 24, 2020 Content Provider Share Posted May 24, 2020 Then you have a hardware problem you need to fix. If you want make a picture of the controller Link to comment Share on other sites More sharing options...
needavirus Posted May 31, 2020 Author Share Posted May 31, 2020 Hmm, I've posted reply this week, but my message disapperead. ? Nevermind, I post again ? So, Heres the pictures of my board : Yeah, I know, C13 is missing, i've see it when I've taken pictures... (Where was my brain again...) I solder a 100nf on it, but no differences. Still locked on the Gottlieb V1-2-3 splash screen.... Thanks for your help ! ? Link to comment Share on other sites More sharing options...
Content Provider lucky1 Posted May 31, 2020 Content Provider Share Posted May 31, 2020 33 minutes ago, needavirus said: Hmm, I've posted reply this week, but my message disapperead. ? Nevermind, I post again ? So, Heres the pictures of my board : Yeah, I know, C13 is missing, i've see it when I've taken pictures... (Where was my brain again...) I solder a 100nf on it, but no differences. Still locked on the Gottlieb V1-2-3 splash screen.... Thanks for your help ! ? I already replied to it but that got also deleted. I assume you have soldered the wrong resistor array. You need a isolated array and not a bussed. On the picture here you see the difference https://de.wikipedia.org/wiki/Datei:Widerstandsnetzwerk.svg You need the one in the lower part of the picture. Link to comment Share on other sites More sharing options...
needavirus Posted May 31, 2020 Author Share Posted May 31, 2020 Ok, is this OK if I change thooses arrays with links of singles resistors ? What is the good value of theeses ? I've forgoted it... Thanks ! Link to comment Share on other sites More sharing options...
needavirus Posted May 31, 2020 Author Share Posted May 31, 2020 Yeay ! Ok, I've found this again, 220Ohms Thanks to the SEARCH button ? So i've changed this stupid array with 220ohms singles res, and of course IT WORKS !! Many Many thanks for your help again Lucky !! ??? Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.