Curbfeeler Posted February 22, 2016 Share Posted February 22, 2016 Have two sets of complete stm32 and lucky1 (version 1.2) boards assembled, will sell for my actual cost $70 shipped cont us. Don't need them, but they were fun to play with. Must buy both, as I just want to mail off one package and be done. Edit with revision info : Went through sasha's posts. The only difference between this and current 1.4 are as follows. changelog from 1.2 to 1.3: *Addition of extra hub75 to allow clone of display as topper. changelog from 1.3 to 1.4: * EXT Power Screw Terminal AND * EXT Power Pin Header * Screw holes with 65mm distance (same distance as the screw holes in the DMD) * PCB size is a little bit bigger. I'll ship 'em quick, no waiting! Dan Sent from my SM-G900V using Tapatalk Link to comment Share on other sites More sharing options...
Content Provider UncleSash Posted February 24, 2016 Author Content Provider Share Posted February 24, 2016 @ Dan: Your Changelog is correct. There is no big change in the rev 1.x´s. But why you want to sell them? @ ALL: Everybody can Order again! Rev 2.0 is still in Stock with 17 pcb's! And I still have some rev 1.4 Shields! You may get a Discount on the rev 1.4 Set's ... just ask! - Sascha Link to comment Share on other sites More sharing options...
djbrh Posted February 24, 2016 Share Posted February 24, 2016 Okay, back on the market. One complete Package E Rev2 board. $50 shipped CONUS. Email [email protected] if interested. --Donnie Link to comment Share on other sites More sharing options...
Curbfeeler Posted February 27, 2016 Share Posted February 27, 2016 @ Dan: Your Changelog is correct. There is no big change in the rev 1.x´s. But why you want to sell them? - Sascha Decided not to sell, going to try again to get them working. When we last tried in a real pinball it was very early and we had issues with glitches, but obviously a lot of code updates since so we will give it another go.Sent from my SM-G900V using Tapatalk Link to comment Share on other sites More sharing options...
Content Provider UncleSash Posted February 28, 2016 Author Content Provider Share Posted February 28, 2016 Decided not to sell, going to try again to get them working. When we last tried in a real pinball it was very early and we had issues with glitches, but obviously a lot of code updates since so we will give it another go. Sent from my SM-G900V using Tapatalk Maybe the Filter PCB is a good choice for use with a real pinball. I got some new in stock next week. When you want to buy one, feel free to contact me. Or I send you one and when it works you pay for it and when not, just send the Filter back to me. - Sascha Link to comment Share on other sites More sharing options...
Content Provider lucky1 Posted February 29, 2016 Content Provider Share Posted February 29, 2016 All others Donations or over pays are staying with me for my work and continues improvements on the Shield Layout! But when you want to Donate more for the Pin2DMD, just Donate to Lucky1, the founder of Pin2DMD! I think this should be made more clear that not all donations go into the charity project, by placing it on top of the post, since some didn´t know that. For legal reasons UncleSash is only allowed to sell the device with a activation key for the basic features (no pinball browser, no pin2dmd editor). You can easly get a full featured Key from me by making a additional donation which goes 100% into charity. Link to comment Share on other sites More sharing options...
Content Provider UncleSash Posted February 29, 2016 Author Content Provider Share Posted February 29, 2016 just added more Informations in the beginning!I hope it is clear now for everybody.When not, just ask me, Link to comment Share on other sites More sharing options...
Content Provider UncleSash Posted March 1, 2016 Author Content Provider Share Posted March 1, 2016 Just an Information for ALL rev 2.0 USER! (EU, US, WORLD!) 5V DC source Selector: Link to comment Share on other sites More sharing options...
Content Provider UncleSash Posted March 1, 2016 Author Content Provider Share Posted March 1, 2016 Updated order - Post #1! Link to comment Share on other sites More sharing options...
djbrh Posted March 8, 2016 Share Posted March 8, 2016 Okay, back on the market. One complete Package E Rev2 board. $50 shipped CONUS. Email [email protected] if interested. --Donnie Still available. Someone buy this, please. --Donnie Link to comment Share on other sites More sharing options...
djbrh Posted March 16, 2016 Share Posted March 16, 2016 Still available. Someone buy this, please. --Donnie It's now sold. --Donnie Link to comment Share on other sites More sharing options...
Content Provider UncleSash Posted March 16, 2016 Author Content Provider Share Posted March 16, 2016 For DAZZ! To fix the problem: hey dazz. something went wrong woth my messager... but here a solution! found here: http://vpuniverse.com/forums/topic/2219-pin2dmd-color-pindmd-compatible-interface-with-led-rgb-color-dmd/?p=24993 I found a solution for "in the script", must be used in each table script! '************ BEGIN PIN2DMD PALETTE RESET **************'************ thanks to Rascal and gtxjoe **************Const PIN2DMDDIR = "D:\010 Pin2DMD\FW\Pin2DMD Tool"Sub ResetPaletteDim rShellDim WScriptSet rShell = CreateObject("WScript.Shell")rShell.CurrentDirectory = PIN2DMDDIRIf PIN2DMD = True then rShell.run "pin2dmd.exe /i blank.ppm",,TRUESet rShell = NothingEnd SubSub table1_exit():Controller.Stop:ResetPalette:End Sub'************* END PIN2DMD PALETTE RESET *************** This line must be modifyed with your Pin2DMD folder!!! Const PIN2DMDDIR = "D:\010 Pin2DMD\FW\Pin2DMD Tool" please try it. and give a feedback! Sascha Link to comment Share on other sites More sharing options...
Content Provider UncleSash Posted March 16, 2016 Author Content Provider Share Posted March 16, 2016 here the PPM fileblank.zip Link to comment Share on other sites More sharing options...
Content Provider UncleSash Posted March 22, 2016 Author Content Provider Share Posted March 22, 2016 SD Card Reader FIX for REV 1.x User Online: http://vpuniverse.com/forums/files/file/4155-dirty-emergency-sd-card-reader-in-diy/ German Version: http://vpuniverse.com/forums/files/file/4156-unsch%C3%B6ner-sd-kartenleser-f%C3%BCr-den-notfall/ Works great! Looks ugly! reards Sascha Link to comment Share on other sites More sharing options...
Content Provider UncleSash Posted April 1, 2016 Author Content Provider Share Posted April 1, 2016 Hello Folks! Some Updates for you! I have 16 pcs Pin2DMD Shield rev 2.0 in Stock! After almost 2 weeks delay (1st my manufacture was late, 2nd wrong Address on the Shippinh label takes also 1 week to get it fixed) And another 20pcs are on the way to the states! I hope we are good prepared for the next couple weeks. regards Sascha Link to comment Share on other sites More sharing options...
ArcadiusMaximus Posted April 5, 2016 Share Posted April 5, 2016 This system is outstanding. Great work all ! PM Sent ! Link to comment Share on other sites More sharing options...
martymoose69 Posted April 8, 2016 Share Posted April 8, 2016 Sent from my iPhone using Tapatalk Here's the FAST Pinball bracket: ImageUploadedByTapatalk1454861666.234186.jpgImageUploadedByTapatalk1454861675.667155.jpg Here's what the 64x64 setup looks like direct from China: ImageUploadedByTapatalk1454861723.988299.jpg I had to take the back plate off, cut it in half, reinstall the two LED boards on each half, then mount each half to the bracket. Looks good. Now just need my controller from UncleSash! --Donnie Both look Fantastic guys i am here in Australia so freight would be a killer to order one i sent a email to [email protected] and got no response i happen to have a days work in a plastics shop monday only they have a cnc guy said if i supply a dxf.file of a drawing he would cut me one up so does anybody have a autocad file of a drawing or a scanned image of the bracket with measurements thanks in advance Link to comment Share on other sites More sharing options...
Content Provider lucky1 Posted April 8, 2016 Content Provider Share Posted April 8, 2016 Here is the frame design from Rappelbox he published in the german forum. The svg file can easily be converted to dxf . PIN2DMD_Frame.zip Link to comment Share on other sites More sharing options...
martymoose69 Posted April 8, 2016 Share Posted April 8, 2016 Here is the frame design from Rappelbox he published in the german forum. The svg file can easily be converted to dxf . Fantastic again thanks mate Link to comment Share on other sites More sharing options...
Content Provider UncleSash Posted April 19, 2016 Author Content Provider Share Posted April 19, 2016 Frames are back in Stock... Link to comment Share on other sites More sharing options...
ArcadiusMaximus Posted April 24, 2016 Share Posted April 24, 2016 So I received my "RGB" displays today only to find out they are "GRB". The link to the sale on A.E. is now changed to GRB too. Does anyone one have a reliable seller of compatible panels? 3 weeks of waiting down the drain... Oh well. Link to comment Share on other sites More sharing options...
martymoose69 Posted April 24, 2016 Share Posted April 24, 2016 So I received my "RGB" displays today only to find out they are "GRB". The link to the sale on A.E. is now changed to GRB too. Does anyone one have a reliable seller of compatible panels? 3 weeks of waiting down the drain... Oh well. Link to comment Share on other sites More sharing options...
martymoose69 Posted April 24, 2016 Share Posted April 24, 2016 Think it is a typo I click on the panel's I ordered and there identical except the rgb word Have you tested? Link to comment Share on other sites More sharing options...
Content Provider lucky1 Posted April 24, 2016 Content Provider Share Posted April 24, 2016 There are really GRB panels out there which are not compatible with pin2dmd firmware. Unfortunately I don´t have one to find out what the problem is. If somebody has one and is capable of modifying C code, he can try V1 source to do so and forward the info to me and I can insert the changes into V2. Link to comment Share on other sites More sharing options...
martymoose69 Posted April 24, 2016 Share Posted April 24, 2016 Really. Wow i would be asking for a refund Maybe email them ask them to remove the pin2dmd of there description untill a fix is found Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.