clems80 Posted January 7, 2019 Share Posted January 7, 2019 hello, I built a pin2dmd xl for my dataeast maverick, but he has a concern for image shift on the right side, I reversed 2 led panel but the same. have seen an idea to solve my problem Link to comment Share on other sites More sharing options...
clems80 Posted January 7, 2019 Author Share Posted January 7, 2019 I exchange LED panels, Hud cable, power cables, flash firmware st and pin2dmd (news 2.60), check welds but nothing to always bugs .. Link to comment Share on other sites More sharing options...
Content Provider lucky1 Posted January 7, 2019 Content Provider Share Posted January 7, 2019 Try firmware 2.11 https://github.com/lucky01/PIN2DMD/blob/b795859081d7c8bddd8b400f7045ecfcc3e26450/firmware/latest/V4 NUCLEO-144/PIN2DMD_XL.bin Link to comment Share on other sites More sharing options...
Content Provider lucky1 Posted January 7, 2019 Content Provider Share Posted January 7, 2019 Are you sure that it is a Nucleo 429ZI ? Link to comment Share on other sites More sharing options...
clems80 Posted January 7, 2019 Author Share Posted January 7, 2019 Yes is 429ZI 2.11 gives a different bug I upload the video Link to comment Share on other sites More sharing options...
clems80 Posted January 7, 2019 Author Share Posted January 7, 2019 Link to comment Share on other sites More sharing options...
Content Provider lucky1 Posted January 7, 2019 Content Provider Share Posted January 7, 2019 Please make a closeup picture of the ICs on the backside of the panels that I can read the type. Link to comment Share on other sites More sharing options...
Content Provider lucky1 Posted January 7, 2019 Content Provider Share Posted January 7, 2019 8 minutes ago, clems80 said: https://youtu.be/BrxTSuxAEow Cant view it. Link to comment Share on other sites More sharing options...
clems80 Posted January 7, 2019 Author Share Posted January 7, 2019 1 minute ago, lucky1 said: Cant view it. It's good for the video Link to comment Share on other sites More sharing options...
Content Provider lucky1 Posted January 7, 2019 Content Provider Share Posted January 7, 2019 Shows "Video not available" Link to comment Share on other sites More sharing options...
Content Provider lucky1 Posted January 7, 2019 Content Provider Share Posted January 7, 2019 Please measure the voltage. Were do you get the power from ? Link to comment Share on other sites More sharing options...
clems80 Posted January 7, 2019 Author Share Posted January 7, 2019 Link to comment Share on other sites More sharing options...
clems80 Posted January 7, 2019 Author Share Posted January 7, 2019 Link to comment Share on other sites More sharing options...
clems80 Posted January 7, 2019 Author Share Posted January 7, 2019 the references of the chips give a result? Link to comment Share on other sites More sharing options...
Content Provider lucky1 Posted January 7, 2019 Content Provider Share Posted January 7, 2019 Please turn down the voltage to 4.8V Link to comment Share on other sites More sharing options...
clems80 Posted January 7, 2019 Author Share Posted January 7, 2019 Bingo !! Thank you very much do I update to 2.60? Link to comment Share on other sites More sharing options...
Content Provider lucky1 Posted January 7, 2019 Content Provider Share Posted January 7, 2019 Yes please also try the latest Link to comment Share on other sites More sharing options...
clems80 Posted January 7, 2019 Author Share Posted January 7, 2019 -with 2.60 it's still the same bug -I put the 2.11 it works again on the other hand when I put the SD with the .DAT and .PAL created with pin2dmd.exe new version the pin2dmd turns on then goes off in 3s, one must surely the old pin2dmd.exe !? Link to comment Share on other sites More sharing options...
clems80 Posted January 7, 2019 Author Share Posted January 7, 2019 I managed to access the menu by quickly pressing the buttons and made a save config with the inserted sd, so it does not cut more, but it only works with the 2.11 Link to comment Share on other sites More sharing options...
dpannell2 Posted January 7, 2019 Share Posted January 7, 2019 I just tested one of those and it worked fine. I believe it was firmware 2.55 Link to comment Share on other sites More sharing options...
Content Provider lucky1 Posted January 8, 2019 Content Provider Share Posted January 8, 2019 10 hours ago, clems80 said: -with 2.60 it's still the same bug -I put the 2.11 it works again on the other hand when I put the SD with the .DAT and .PAL created with pin2dmd.exe new version the pin2dmd turns on then goes off in 3s, one must surely the old pin2dmd.exe !? Selecting the devicemode and creating a pin2dmd.dat in pin2dmd.exe for a 192x64 is currently not supported. Use it only for creating a pin2dmd.pal I will see if I can reproduce that problem with V2.60. For now take V 2.11 there is no difference in functionality. Link to comment Share on other sites More sharing options...
Content Provider lucky1 Posted January 8, 2019 Content Provider Share Posted January 8, 2019 11 hours ago, dpannell2 said: I just tested one of those and it worked fine. I believe it was firmware 2.55 I just tested and could not reproduce the problem. Looks like a memory error to me. @dpannell2 Do you have some of those panels and could test with 2.60 XL firmware please ? Link to comment Share on other sites More sharing options...
dpannell2 Posted January 8, 2019 Share Posted January 8, 2019 I guess it was 2.12 that I tested it with. I'm seeing the same issue, see pics. Link to comment Share on other sites More sharing options...
Content Provider lucky1 Posted January 8, 2019 Content Provider Share Posted January 8, 2019 4 hours ago, dpannell2 said: I guess it was 2.12 that I tested it with. I'm seeing the same issue, see pics. I sent you an e-mail. Link to comment Share on other sites More sharing options...
Content Provider lucky1 Posted January 9, 2019 Content Provider Share Posted January 9, 2019 With a lot of testing from Dan we finally found the problem. I will upload the new release 2.61 tomorrow. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.