Jump to content

teensy 3.2 and adaptor board problems


Recommended Posts

I have a teensy 3.2 and adaptor board hooked up to my visual pinball . When I load a table the led  on the teensy  flashes very fast like it working. but I get no leds im using  144 m leds cut in half one for left side and other  for the other side  could it be my Ethernet cable attached to the leds or the usb cable

Link to post
Share on other sites

I have that to .the teensy led flashes every second  then when I load table it flashes like hundred mile an hour like it's working but I get no addressable leds could it be the ethernet cable I checked all my solder joints even reflow ed then to make sure there good.

Link to post
Share on other sites

I have orange wired to data line white line to ground and the red for power and white ground on to power supply .the same for the blue side which I'm using is 5v 30a power supply . I now have only one or two leds working there is 72 leds on one strip there was 144m but I cut them in half for each side .

Link to post
Share on other sites

Try This

 

<?xml version="1.0"?>
 <Cabinet xmlns:xsi="http://www.w3.org/20...Schema-instance" xmlns:xsd="http://www.w3.org/2001/XMLSchema">
   <Name>TimoPin</Name>
    <OutputControllers>

     
     <TeensyStripController>
      <Name>LEDStripController</Name>
       <NumberOfLedsStrip1>72</NumberOfLedsStrip1>
       <NumberOfLedsStrip2>72</NumberOfLedsStrip2>
       <NumberOfLedsStrip3>0</NumberOfLedsStrip3>
       <NumberOfLedsStrip4>0</NumberOfLedsStrip4>
       <NumberOfLedsStrip5>0</NumberOfLedsStrip5>
       <NumberOfLedsStrip6>0</NumberOfLedsStrip6>
       <NumberOfLedsStrip7>0</NumberOfLedsStrip7>
       <NumberOfLedsStrip8>0</NumberOfLedsStrip8>
       <ComPortName>COM5</ComPortName>
     </TeensyStripController>
     
    </OutputControllers>
    
    <Toys>
 

     <LedStrip>
       <Name>PF Right</Name>
       <Width>1</Width>
       <Height>72</Height>
       <LedStripArrangement>TopDownLeftRight</LedStripArrangement>
       <ColorOrder>GRB</ColorOrder>
       <FirstLedNumber>1</FirstLedNumber>
       <FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
       <OutputControllerName>LEDStripController</OutputControllerName>
     </LedStrip>
    
    
     <LedStrip>
       <Name>PF Left</Name>
       <Width>1</Width>
       <Height>72</Height>
       <LedStripArrangement>TopDownRightLeft</LedStripArrangement>
       <ColorOrder>GRB</ColorOrder>
       <FirstLedNumber>73</FirstLedNumber>
       <FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
       <OutputControllerName>LEDStripController</OutputControllerName>
     </LedStrip>
     

    <LedWizEquivalent>
    <Name>LedWizEquivalent 30</Name>
     <Outputs>
     <LedWizEquivalentOutput>
      <OutputName>PF Right</OutputName>
      <LedWizEquivalentOutputNumber>1</LedWizEquivalentOutputNumber>
     </LedWizEquivalentOutput>
      <LedWizEquivalentOutput>
      <OutputName>PF Left</OutputName>
      <LedWizEquivalentOutputNumber>4</LedWizEquivalentOutputNumber>
     </LedWizEquivalentOutput>
     </Outputs>
     <LedWizNumber>30</LedWizNumber>
     </LedWizEquivalent>
    </Toys>
  <AutoConfigEnabled>true</AutoConfigEnabled>
</Cabinet>

Link to post
Share on other sites

Do u think I'm doin something wrong with the teensy board I install the newest firmware  teensystripcontroller beta but im not sure what todo with the source code if I do anything and also I'm confused about wiring it up do I add ground or power to the teensy board 

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...