HomerRamone Posted June 15, 2020 Share Posted June 15, 2020 Was fiddling with my p2dmd today. Looking to see what version it was and wondering if it can be upgraded to the latest version. I managed to find the version - 2.32 but ive also managed to get it stuck. Now when it powers on all I get is the logo with "STERN SAM" underneath. If turn it off and remove the SD card then turn it back on this changes to "VIRTUAL PINBALL" but when I put the card back im right back at "STERN SAM" Tried holding buttons down but all I can seem to do is reset it. What have I done ? (Also - can it be upgraded to 3.x? ) Thanks Link to comment Share on other sites More sharing options...
Content Provider lucky1 Posted June 15, 2020 Content Provider Share Posted June 15, 2020 You don´t seem to have user buttons installed on your shield pcb. The blue onboard button has no function and the black onboard button is reset. Remove the pin2dmd.dat file from your SD card to get it into vpin mode with SD card inserted. For instructions how to upgrade your device please read https://pin2dmd.com/installation/ Link to comment Share on other sites More sharing options...
HomerRamone Posted June 15, 2020 Author Share Posted June 15, 2020 Thanks for the super speedy reply ! Forgot post. This is in a "real" pin rather than attached to a virtual table. Link to comment Share on other sites More sharing options...
Content Provider lucky1 Posted June 15, 2020 Content Provider Share Posted June 15, 2020 Please check the orientation of your ribbon cable. Link to comment Share on other sites More sharing options...
HomerRamone Posted June 15, 2020 Author Share Posted June 15, 2020 Ive managed to get it back on. (Not sure exactly what I did but nevertheless its working again) Headed to the upgrade guide, ran the dfuse util which went thru what appeared to be correct phases. That is to say it said "Erasing" then "updating". Said it was done. Power cycled.. and it still shows as ver 2.32 Link to comment Share on other sites More sharing options...
Content Provider lucky1 Posted June 16, 2020 Content Provider Share Posted June 16, 2020 Could you make a picture of your hardware ? Link to comment Share on other sites More sharing options...
HomerRamone Posted June 16, 2020 Author Share Posted June 16, 2020 Link to comment Share on other sites More sharing options...
Content Provider lucky1 Posted June 16, 2020 Content Provider Share Posted June 16, 2020 That is a custom hardware from pinballSP which I don´t have, but as far a I know you should set the Boot DIP switch and then use the DFUSE Utility. Download this file https://github.com/lucky01/PIN2DMD/raw/master/firmware/latest/V3 STM32F4 DISCOVERY/pin2dmd.dfu and use Upgrade and Verify action as described here https://pin2dmd.com/installation/ Link to comment Share on other sites More sharing options...
HomerRamone Posted June 17, 2020 Author Share Posted June 17, 2020 Yeah - thats what I tried yesterday. Tried it again and it seems to work - as in says its erasing, then uploading then verifies. But on boot it still says 2.32 Link to comment Share on other sites More sharing options...
Content Provider lucky1 Posted June 17, 2020 Content Provider Share Posted June 17, 2020 Then you most likely have overwritten your download file with your current image by using the upload and not the upgrade function of the DFU tool. Please download the firmware again and use the upgrade function and NOT the upload function Link to comment Share on other sites More sharing options...
HomerRamone Posted June 17, 2020 Author Share Posted June 17, 2020 Did its again just to be sure - and somethings happened - now i just get a black screen Link to comment Share on other sites More sharing options...
HomerRamone Posted June 17, 2020 Author Share Posted June 17, 2020 Ok, Scratch that. Finally got it working \o/ Thanks for you help ! Link to comment Share on other sites More sharing options...
HomerRamone Posted September 10, 2022 Author Share Posted September 10, 2022 OK, its been a while. And this has been working great. However I just tried to update to v 4.41 so I can run the gold colourizations. Tried updating with the .upd from the V3 STM32F4 DISCOVERY folder but it just says "Invalid update". Can I not run this firmware with my board Thanks Link to comment Share on other sites More sharing options...
HomerRamone Posted September 10, 2022 Author Share Posted September 10, 2022 Urgh. I am a fool at times. Now updated to 4.41. (Lets just call it user error). Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now