Jump to content
Search In
  • More options...
Find results that contain...
Find results in...
lucky1

Color Bleeding Of Chinese Rgb Panels

Recommended Posts

Not unless the solider joints on the mosfet get hot and cause dried joints btw can someone's make a sheld for vpinball mame only as the real pinball no real use to me but they are inputs from the pinball mcu board

Share this post


Link to post
Share on other sites

"10 years electronics experience"

*looks at circuit "schematics" being posted*

:rolleyes:

  • Upvote 1

Share this post


Link to post
Share on other sites

I got one ali express seller backing this fix we he will send me a free sample panel as my low 8 watt solidering iron screw the chips up i going to use solidering glue on the chip pin and solder the transisters on the copper

Share this post


Link to post
Share on other sites

Wow the pod do work can turn the brightness up and down may be a 1 ohm resister to be continued and add a extra pod for brightness and copyright da macker 2016 ps the last picture is a 201 pod from a commodore 64 tape deck motor and the shift register is fine put between g1 pin and oe check last pictures of metre test

post-11003-0-75243000-1472294075_thumb.jpg

post-11003-0-94482800-1472294139_thumb.jpg

post-11003-0-45210800-1472294828_thumb.jpg

post-11003-0-35893800-1472294979_thumb.jpg

post-11003-0-77587900-1472295074_thumb.jpg

post-11003-0-05358500-1472295244_thumb.jpg

post-11003-0-94097700-1472295589_thumb.jpg

post-11003-0-02110800-1472301413_thumb.jpg

post-11003-0-36754800-1472301478_thumb.jpg

post-11003-0-85990900-1472349727_thumb.png

Share this post


Link to post
Share on other sites

Transister glue with super glue to pcb adding stm 1206 size 1k ohm and wire glue to chip fet legs and solider transister end to copper wire bridge worked 100% only did one panel each set and it seems to fix the ones in the dasiy chain

post-11003-0-03039400-1472561263_thumb.jpg

post-11003-0-37291500-1472561335_thumb.jpg

Share this post


Link to post
Share on other sites

Why is this p3 2015 version has diffent 4 ic on this board sm 5166p at t1 t2 t3 t4 has replaced the 16 x 4953 anyone noticed this and these work 100% slight bleed on the edge  but not as bad this seller 100 % recommend  all pictures have the same sm chips and no 4953 as below can anyone point me to a pinout onof 5166p 16 pin dip ic they called 

NIPPON PRECISION CIRCUITS  SM5160CM  FREQ SYNTHESISER PLL, 5160, SOIC16

All of our led modules has no blanking

Plus look at bottom picture these old panels was made 2013 06 01 with the 4953

Updated information

If the.gio pin on the real pinball input are unused while using vpinmame usb these pin are.exposed and need to be bridged to stop colour bleed that why the new stm without shield dont show signs of this problem

And prehapes this changing the cystal osolator to a 25 mhz 

http://andybrown.me.uk/2015/03/03/modding-the-stm32-f4-discovery-with-a-25mhz-clock/

Add the -5 volt + 3 gnds on hub75 may also help bleeding as good gounding is key maybe diods the 6 rgb inputs from the stm32 discovery 

 

 Cheers paul

20160905_111018.jpg

Screenshot_2016-09-05-12-19-57.png

Screenshot_2016-09-05-20-08-47.png

Screenshot_2016-09-05-20-12-34.png

 

1473193519770709256841.jpg

IMG_20160907_092219_1757354230.jpg

Edited by paul
New info

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...