Jump to content
Search In
  • More options...
Find results that contain...
Find results in...


  • Content Count

  • Joined

  • Last visited

Community Reputation

2 Neutral

About latenite04

  • Rank

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. If you just want a kit with all the parts to solder the shield yourself I've got a blank shield pcb and parts left over from when I ordered everything. Just send me a pm.
  2. That should work. Here's a picture of the back of one of mine. The red is +5v and black is ground going to the shield and the led panels.
  3. It looks like the Nucleo board still needs the stock headers clipped and the outside ones soldered on.
  4. Great write up. If anyone is looking to build one for a physical machine and needs to populate the rest of the board here is the parts list I used for my build. Here's another option for the frame if you have access to a 3d printer: https://www.thingiverse.com/thing:3098697 Pin2DMD Parts.pdf
  5. Thanks for the test file. I should have time this weekend to try it. I'll let you know how it goes.
  6. I tried swapping the controllers and changing the enhancer settings but neither fixed the issue. My logic analyzer arrived today in the mail. Is there a write up on how to create the signal recording?
  7. Thanks. I'll try swapping controllers just to see if it changes anything and I ordered a logic analyzer.
  8. I only know of 1 version of roms for this machine. It's the smaller 3/4 size mario machine not the full sized one. https://www.ipdb.org/machine.cgi?id=3427
  9. Thanks for your time and the info. I'll try swapping display controllers and try to find out if there are other display roms.
  10. The only files on the sd card are the key file and the pin2dmd.dat file with the config settings so it's running off of the pinball machine's roms. As far as I know there are no colorization files for this machine yet, I was hoping to do the dump and try coloring it. I was under the impression that this would act like a normal dmd even without those files. I did put the pal and fsq files from the other mario machine's project on the sd card once just to see if it would make a difference but I had the same issue.
  11. I tried the display in my machine again and it is having the same issue. I also tried a second display and power supply and swapping the ribbon cable with the one from my street fighter. Both displays work on street fighter and are having the same issue on mario. I looked through scottyc's info from his mario colorization and unfortunately he has the 3.1 shield from german gaming so it's not a direct comparison but i did notice that he had the 2.41 firmware installed. @lucky1 do you have an older version of the firmware for the nucleo-144/shield v4 that I could try? I currently have 2.58 installed.
  12. Thanks for the reply @lucky1. I'm getting power from a dedicated 5v 10A power supply. I checked it and it was a little high, 5.15v, so I adjusted it down to 4.9v. Hopefully I have time in the next few days to try it in the machine again.
  13. I hooked up my display to my Super Mario Mushroom World machine and the image on the display is somewhat scrambled. I hooked up the old dmd and that works fine. I also connected my pin2dmd back up to my Street Fighter and the display is working correctly on that machine. I'm hoping it's a setting issue but I tried using the Gottlieb V1, v2, and v3 modes and they all looked about the same. This is running on a v4 shield with the latest firmware from github. Thanks in advance for any help.
  14. I designed a 3d printed frame to use with the v4 shield. With the shield being direct mounted to the panels on the left side the center of my panels didn't have much support and I was getting a lot of flex and a gap in the middle of the screens. I went with a 3 piece frame so the middle would not have a joint. The gottlieb machine I was mounting it in didn't use the center mounting holes so I modeled it to take an 8/32 nut so I can use a screw to level it out if I do get any gap. https://www.thingiverse.com/thing:3098697
  • Create New...